A heatsink can be stuck on your CPU to cool it down. That heatsink feels cold when the system is not turned on. However when the CPU is turned on the heatsink is extremely hot. Isn't that contradictory to a certain extent? I expect a heatsink to always be cold and to have the air blowing system turned on for convection purposes.

Could someone explain what is wrong in the way I see things?

  • 63
    $\begingroup$ The heatsink is cold, relatively speaking... $\endgroup$
    – jiggunjer
    Aug 22, 2016 at 13:07
  • 14
    $\begingroup$ Touch the back plane of your fridge, its temperature will most probably surprise you. $\endgroup$ Aug 22, 2016 at 14:34
  • 33
    $\begingroup$ where do you think the heat in the heatsink come from? $\endgroup$
    – njzk2
    Aug 22, 2016 at 17:17
  • 5
    $\begingroup$ The maximum rated temperature a CPU can operate at without errors (T_Jmax) is typically around 100 degrees C for modern CPUs, and they can get up to 90 C before they even start to thermally throttle. There's plenty of room for a heat-sink to feel uncomfortably hot while still being cooler than a CPU under load. If even the idle temps are very high, that's less normal. Software can read the CPU's built-in temp sensors, e.g. using the lm-sensors package on Linux. $\endgroup$ Aug 23, 2016 at 7:18
  • 13
    $\begingroup$ @sgroves: He care's because he's interested in the physics behind it. If everybody wouldn't care about things, we'd still be trying to survive against bears etc. $\endgroup$
    – phresnel
    Aug 23, 2016 at 9:38

9 Answers 9


"I expect a heatsink to always be cold"

The purpose of the heat sink is to transfer heat. The rate of heat transfer depends in a complicated way on (a) the temperature difference between heat sink and air, (b) the exposed surface area, and (c) the air speed.

The heat sink is at its most effective if it is at the same temperature as the CPU. This is because this gives the maximum temperature difference between heat sink and air. This is why heat sinks are often made of copper: copper conducts heat well.

Let us suppose that the CPU is producing heat $Q$ (Watts) and that the heat sink transfer heat at a rate linear with the temperature difference:

$$ Q = K_\text{eff} (T_\text{CPU} - T_\text{air})$$

where $K_\text{eff}$ is the effective heat transfer coefficient. Solving for the CPU temperature:

$$ T_\text{CPU} = T_\text{air} + Q / K_\text{eff}$$

So, the CPU temperature is lowest when $K_\text{eff}$ is highest and $K_\text{eff}$ is highest when the heat sink, due it to having high thermal conductivity, is at nearly the same temperature as the CPU.

  • 63
    $\begingroup$ @trilolil The purpose of the heatsink is to touch lots of air, because when a hot thing touches a cold thing the cold thing gets hotter and the hot thing gets colder. The purpose of the fan is to blow the hot air out of the way after the heatsink heats it up, and replace it with cold air, because if the heatsink was only touching hot air it wouldn't be able to cool down very well. $\endgroup$
    – user253751
    Aug 22, 2016 at 4:09
  • 8
    $\begingroup$ @Aron The usual model for an ideal heat sink is that, while convective heat transfer is finite, the heat sink itself has infinite conductivity. This is part of the concept of "fin efficiency," as discussed here or here for example. If the heat sink has infinite conductivity, then it is at the same temperature as the CPU. Any reduction in the thermal conductivity reduces the overall heat transfer and makes the heat sink less effective. $\endgroup$
    – John1024
    Aug 22, 2016 at 4:23
  • 7
    $\begingroup$ @trilolil You can contrast it with what happens if you have a CPU without a heatsink - the CPU doesn't touch very much air because it's small, so it doesn't heat up the air very much, so it doesn't cool down very much. Also because it's smaller it heats up and cools down quickly, you don't want that because you want to have time to turn it off before it melts. $\endgroup$
    – user253751
    Aug 22, 2016 at 5:56
  • 7
    $\begingroup$ @trilolil Note that for very old CPUs (and nowadays, things like the Northbridge), the heatsink was enough, no fan needed. There's a certain amount of heat the heatsink can get rid of on its own, simply through convection (air gets hot from contact with the heatsink, rises and carries the heat away, while "sucking in" cold air). Fans are not necessary (and neither is strictly speaking the heatsink), they just help with the cooling. You can still build 100% fanless computer today, it just requires much bigger heatsinks :) $\endgroup$
    – Luaan
    Aug 22, 2016 at 8:11
  • 7
    $\begingroup$ @trilolil "the purpose of metal of the heatsink itself is not to cool down the CPU but rather to be able to transfer it [...] the purpose of the built-in fan is to cool down the CPU" The heatsink cools the CPU by transferring heat out of it. The air cools the heatsink by transferring heat out of the heatsink. The fan blows the the hot air away and replaces it with cold air. The new batch of cold air transfers more heat out of the heatsink. As long as heat is leaving the heatsink, more heat can flow out of the CPU into the heatsink. Heat leaves the heatsink fastest when it's hottest. $\endgroup$ Aug 22, 2016 at 10:53

In general, a heatsink should feel hot, if it's doing its job right. If it feels hot, that means it's transferring energy to your hand, which means it's transferring energy away from the CPU.

This also holds for other cooling things. The cooling coils on a fridge or an old A/C should feel hot for the same reason: the heat you're taking away has to be dumped somewhere. If the cooling coils themselves felt cold, your fridge would be working in reverse; it'd be heating up your food.

  • 3
    $\begingroup$ "Conversely if it felt cool, it'd be heating up the CPU" - no. $\endgroup$ Aug 22, 2016 at 22:48
  • 1
    $\begingroup$ @JanDvorak Actually, yes. The only way to make it cool in the first place is to dump heat from the heatsink to the CPU, by an active mechanism. $\endgroup$
    – knzhou
    Aug 22, 2016 at 22:50
  • $\begingroup$ You're suggesting a heat pump from the air to the CPU. But since we have such powerful heat pumps handy, why not have them pump heat to air far away from the CPU? This would then cool down the CPU as well as any organic stuff on top of it. This suggestion of mine should even be less power hungry than your one. $\endgroup$ Aug 22, 2016 at 22:59
  • 3
    $\begingroup$ The point is, if you want to dissipate heat by radiation, which is what a heatsink does, you want the heatsink to be as hot as possible, not cool. $\endgroup$
    – knzhou
    Aug 22, 2016 at 23:06
  • 6
    $\begingroup$ If it felt cool it might be heating up the air and cooling both your hand and the CPU. $\endgroup$
    – user253751
    Aug 22, 2016 at 23:19

The goal of the heat sink is to improve heat flux from CPU to surrounding air. Heat flow is a function of the area of contact and the temperature difference. By adding a component that increases the area, you increase one factor; but it's worth remembering that the heat sink will have to have a temperature between that of the CPU and the air: if it's at the same temperature as the CPU, no heat flows from the CPU to the heat sink; it it's at the same temperature as the air, no heat flows to the air.

In practice, it's easy to make the thermal resistance between the heat sink and the CPU packaging quite low (note - the chip is typically quite a bit hotter than the package, and it's only the latter that touches the heat sink). So with the conductivity between CPU and heat sink being better than conductivity from heat sink to air, the heat sink will tend to a temperature close to that of the CPU.

  • 3
    $\begingroup$ I like this answer because it seems to match the "level" of the question whereas the other answers break down into formulas which are greek to lay people like me. $\endgroup$ Aug 23, 2016 at 15:00

When a heat sink is in intimate contact with a source of heat, like a CPU, heat is transferred in accordance with Newton's Cooling Law:

$$\frac{\mathrm dQ}{\mathrm dt}=uA(T_\textrm{CPU}-T_\textrm{Sink})$$

Where $u$ is a heat transfer coefficient (CPU to sink) and $A$ is the area of contact between the CPU and the heat sink.

Note that $\frac{\mathrm dQ}{\mathrm dt}$ is the heat carried off from the CPU per unit of time.

Higher values of $T_\textrm{Sink}$, as the basic formula shows, actually decrease $\frac{\mathrm dQ}{\mathrm dt}$, which becomes effectively zero when $T_\textrm{CPU}-T_\textrm{Sink}=0$.

To prevent this from happening, the heat sink itself has to transfer accumulated heat, usually to the surrounding air, in which case another heat transfer equation comes into play:

$$\frac{\mathrm dQ}{\mathrm dt}=hA_\textrm{Sink}(T_\textrm{Sink}-T_\textrm{air})$$

Where $h$ is the convection heat transfer coefficient (sink to air) and $A_\textrm{Sink}$ the sink's surface area exposed to the air. $h$ is very dependent on speed or airflow which explains why forced air circulation (fan assisted ventilation) is often used.

In steady state ($T_\textrm {CPU}\approx \text{Constant}$), we have, with $\dot{Q}_\textrm{CPU}$ power generated by the CPU:






The influence of the various factors on $T_\textrm{CPU}$ can be readily appreciated.

Ingenious ways of increasing both $h$ (apart from forced circulation) and $A_\textrm{sink}$ to lower $T_\textrm{CPU}$ have been used like cooling fins or this design (ST-HT4 CPU Cooler Riser):

ST-HT4 CPU Cooler Riser

The highly heat conductive copper bands mostly release the heat from the U-bends.

  • 12
    $\begingroup$ Those 'copper bands' aren't solid copper; they're almost certainly heat pipes, which are significantly better heat conductors. That device won't improve cooling performance; it simply allows you to shift the cooler further from the CPU without a massive reduction in performance. $\endgroup$ Aug 22, 2016 at 8:29
  • $\begingroup$ @SomeoneSomewhere is right. these are common in laptops allowing the fan to not sit directly on top of the CPU. $\endgroup$
    – Chris H
    Aug 22, 2016 at 10:20
  • 4
    $\begingroup$ @DanielSank a search confirms the 4 copper tubes are heat pipes. The Wikipedia heat pipe page lists a heat pipe at roughly 200 times more thermally conductive that copper. $\endgroup$ Aug 22, 2016 at 20:07
  • $\begingroup$ Also note they took the effort to have the heat pipes directly touch the CPU, instead of the much cheaper and more common solution of embedding them in a block of copper which touches the CPU. $\endgroup$
    – Chuu
    Aug 23, 2016 at 20:05
  • $\begingroup$ Anyone who understands this answer wouldn't have needed to ask the question. $\endgroup$
    – user184411
    Aug 26, 2016 at 16:48

Heat flows can be modeled like electric currents. Temperature differences correspond to voltage differences, and the heat flowing is similar to an electric current. In both cases, the two are approximately linear, and we can define the coefficient as a resistance value.

Now, if the resistance is zero, we'd see that there will be no temperature or voltage difference; if infinite there won't be any flow. Both are of course ideal cases.

So, back to the CPU cooler. The goal here is to move a lot of heat from the CPU to the air. This requires a low resistance - high flow, low temperature differences. But the resistance here has two parts: moving the heat from CPU to cooler, and from cooler to the air. These are of course resistances in series, so they add up. (just like electricity). To minimize the sum, we need to minimize both resistances. And the temperature in between (top of cooler) will be dictated by the ratio of the two resistances.

An engineering observation is that moving heat from a solid to the air isn't very effective. Air has a rather low heat capacity per volume, as it's so thin. Adding a fan helps with the volume of air, but it's going to remain the bigger resistance of the two.

SO, just as two electric resistors form a voltage divider, two thermal resistances divide the temperature. The top of the cooler will be somewhere between the CPU temperature and the ambient air, and engineering tells us it's going to be closer to the former.


I'm going to answer this in a far more general way: You don't make cold, You move heat.

Think about an air conditioner: The bits outside get very, very hot. What it's doing is expending mechanical work to move heat from from the inside to the outside. The heat hasn't vanished and cold hasn't been created, the thermal energy has just been moved around.

Unlike an air-conditioner, a normal CPU heatsink is a completely passive system. It can't directly move the heat but it does provide it a highly-conductive place to go, thus pulling at least some heat out of the CPU. Because of the higher area (and more importantly thermal mass) each unit of heat energy is spread thinner over a larger area. The heatsink gets hot, but without it the small thermal-mass of the CPU would be far, far hotter.

Do note that there are some special computer cases with active cooling. This would satisfy your expectation of a cold CPU Heatsink. The mechanical work from the cooling system creates more waste heat than a simple heatsink with fans, but that heat is being dumped from the system so it doesn't affect CPU temperature.


Already good physics answers. Here comes an everyday metaphor which doesn't require as much physics or mathematics knowledge (I hope).

A heat sink should drain the heat of the thing it is attached to. It should be the points or areas which the heat flows towards. That is what a sink is, a point where something flows into. For example a kitchen sink - that is where all the water flows towards and gets sucked up.

Then of course it will probably be even better at doing this if it is also at the same time able to transfer away heat quickly away from itself - the kitchen sink is more effective if it is not clogged up but able to keep the water it sucks up moving so it flows somewhere else.


everything is relative. while it may feel "hot" when compared to your fingers, i assure you the heat sink is still colder than the cpu itself. moreover, the heat sink's job is simply to move heat from the cpu into the air. as such, the temperature of the heat sink is not important as long as the heat flowing thru it is sufficiently high. the heat sink is an improvement over a cpu-to-air interface because heat flows more quickly both from the cpu to the heat sink and from the heat sink to the air. conduction from the cpu to the heat sink is faster because the heat sink is a better conductor of heat than air. conduction (and radiation) from the heat sink to the air is faster because the heat sink has a larger surface area.


The key here is conductivity, which is simply speaking the speed at which heat moves to/from the object. Objects feel cold or hot not based on merely their own temperature, but also their ability to radiate or conduct that temperature to you. In essence, something only feels hot if it succeeds in warming up the part of the body you're sensing with. The same with cold, it has to result in your body cooling down and actually being cold.

Plastics are notorious poor conductors and respond slowly to heat changes, whereas metals are often good conductors, feeling cold to the touch when cool (they conduct the heat away from your fingers efficiently) and resulting in burns when hot (fast movement of their contained heat into your fingers).

Why are good heat sinks conductive? Well, a heatsink wants to do 3 things: firstly absorb the heat away from the CPU, then move that heat away from the CPU, then finally radiate that heat into the general environment, and it needs to do these things at a rate that reaches equilibrium with the rate heat generation of the CPU at an acceptable effective temperature. In all these cases, conductivity is conducive to these goals.


Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.