# Tagged Questions

The tendency of a force to rotate an object about an arbitrary axis.

0answers
50 views

### What kind of torques cause an object to precess?

In studying precession, my textbook (Taylor's Classical Mechanics) makes the assumption that a top spinning about its symmetric axis, but tipped at an angle $\theta$, will precess nicely so long as ...
0answers
47 views

### The underlying chemical interactions behind torque

I did some searching around, and didn't find any previous topics that address torque in this specific way -- here goes: Say I just have a plain ol' piece of wood -- relatively long in one axis, so it ...
0answers
29 views

### The torque produced in the rotor blades of an axial flow turbine

I want to ask about the torque experienced by a axial flow turbine, and how the torque is related to the ange of attack, or pitch angle of the turbine blades. (I'm new to technical terms, please ...
0answers
223 views

### Maximum friction force for a wheel to be able to roll

The wheel with mass $M$ and radius $R$ below is free in space (it is not on the ground). A torque $\tau$ is applied to it through an engine. A horizontal force $F = \frac{\tau}{R}$ is also applied to ...
0answers
622 views

### Sum of energy in a free rotation with Algodoo software

I try to understand why Algodoo software (freeware) give an efficiency greater than unity. I tested several scenes and at each time I can look the software give energy, I don't say it's all the time ...
0answers
314 views

### Why do control moment gyroscopes exhibit “torque amplification”?

There are a number of articles that describe the benefits of using control moment gyroscopes (CMGs) over reaction wheels in inertial navigation applications. One of the primary benefits of using a CMG ...
0answers
63 views

### Energy to winding or unroll a tube with a gaz under pressure inside

I take a tube with a gas under pressure inside it. The volume of the tube is not constant. When I winding the tube its volume decreases. So, the pressure increases in the same time so I need an energy ...
0answers
42 views

### Are these torques correct for a simple balancing/fulcrum experiment?

For my physics lab, they had us do a simple static equilibrium experiment where we rested a ruler on a fulcrum (at its center of mass) and then attached varying amounts of weight on either end at ...
0answers
27 views

### What is the general proof that the torque acting on an irregular current carrying loop in an uniform magnetic field is only dependent on area?

How do you prove that the torque acting on an irregular current carrying loop in an uniform magnetic field in the plane of loop = $I \vec{A} \times \vec{B}$ Where, $\vec{A}$ = Area vector of the ...
0answers
67 views

### Find the force and the torque so that the cylinder is in balance

At the cylinder of the picture there are static pressures from environment fluid of density $\rho$. If we neglect the atmospheric pressure, calculate how much force and how much torque is needed so ...
0answers
764 views

### Calculating the torque required to move a heavy object (the calculations)

I wanna choose a motor for my bicycle and turn it into an electric one. So the physics part shoots. The force (Force=Mass x acceleration) that i will exert on earth surface(weight) will be my mass*g,...
0answers
72 views

### Question about calculating the torque of a magnet in an additive field

I did an experiment in the lab today where I placed a magnet in between two coiled magnets, with one coiled magnet having its south side up and north side down and the other coiled magnet with the ...
0answers
106 views

### Pressures in multiple hydraulic drive system circuits when driving common drive shaft

Assume that there are two 'idealised' and identical hydraulic drive system circuits each consisting of a connected positive displacement pump and hydraulic motor where both motors (from each ...
0answers
241 views

### Rolling in 3D using Torque, Angular Momentum/Velocity

I'm stuggling to get a simulation working correctly. Below you can see what I am attempting to do. You can also view it here. Can you spot where I'm going wrong? (Calculated at start) 1) Inertia ...
0answers
356 views

### How to measure the energy required to pedal an exercise bike

I have hacked a FitDesk exercise bike to output the RPM of the pedals and the position of the resistance control within its range of travel. I want to characterize the energy that is required to ...
0answers
158 views

### Correct way to calculate torque produced by axle

For my electrical engineering course, we had to build a simple DC motor that can lift a coin. I have tested the motor, and here are the results: rotational speed (no load): 3630 RPM (380 rad/sec) ...
0answers
314 views

### Angular Momentum Conservation in Gravitational Interaction

thanks for any help. I'm trying to show that in a 2body problem, angular momentum is conserved given that $\dfrac{dp}{dt}=\dfrac{-GMm(rv)}{r³}$, where p is momentum, t time, G gravitational constant, ...
0answers
64 views

### Two impulses on body

Suppose I have a physics simulation with a single body with three degrees of freedom (two axis and rotation). I have two impulses of equal magnitude in opposite directions. When applying these ...
0answers
526 views

### Torque, lever and mass

The Force used in a catapult is exerted near its axis. If we double the length of the arm of the catapult, but still use the same Force at the same point as before near the same axis, does the ...
0answers
2k views

### Neglecting friction on a pulley?

So, this is how the problem looks: http://www.aplusphysics.com/courses/honors/dynamics/images/Atwood%20Problem.png Plus, the pulley is suspended on a cord at its center and hanging from the ceiling. ...
0answers
7 views

### most efficient set of weights with whole number mass to n-power for balancing unknown mass on vertex of regular triangle

I saw this qustion: http://puzzling.stackexchange.com/questions/186/whats-the-fewest-weights-you-need-to-balance-any-weight-from-1-to-40-pounds Suppose you want to create a set of weights so ...
0answers
9 views

### Bending and elastic torques origin problem

In the picture, the sheet of metal is hinged and rotated with angular acceleration alpha, bending is quite small. Problem I'm facing is, where is the origin for torque due to elastic forces (M), what ...
0answers
17 views

### How does Torque from tidal forces scale with distance

I read in a paper a while back that the torque on a body caused by differential rotation and tidal forces scaled with distance to the power of 6. That struck me as odd since the tidal force scales ...
0answers
46 views

### Adding multiple torque vectors together to determine resultant torque

I am working in a 2D environment, where there are multiple angular forces (torque) applied at an object. The way I calculated 1 torque "application", was by: ...
0answers
29 views

### flow rate measurement of a fluid

I had an experiment related to piping networks in my institute. In the experiment there was a device that was measuring flow rate based on rotations of a fan-like system. This created a doubt in my ...
0answers
18 views

0answers
104 views

### What is the linear and rotational motions generated by a force not on the CG?

Given a force that is applied to a free body, not directly towards, or away from the centre of gravity, how would you calculate the amount of linear and rotational velocities generated, as the farther ...