0
votes
1answer
76 views

Moment around a point in a frame

Note: Both diagrams are 2d(they might look 3d because I drew them manually.) I have a prismatic frame that looks like this: I made a section on the half of the first pillar(the red line represents the ...
4
votes
1answer
357 views

Why don't couple forces violate Newton's First Law?

If you have some random object at rest and you apply a couple to it, the net force acting on it is zero. However because a moment acts on it, it starts to rotate. So you had an object at rest, a net ...
1
vote
1answer
261 views

Calculating torque in 3D?

Say you have a sphere, and you have several torque vectors acting on it, all at different points. Say you have the vector (6i + 3j + 5k) originating from point A, and the vector (3i + 1j + 9k) ...
2
votes
2answers
159 views

Why is moment dependent on the distance from the point of rotation to the force?

The formula for moment is: $$M = Fd$$ Where F is the force applied on the object and d is the perpendicular distance from the point of rotation to the line of action of the force. Why? Intuitively, ...
0
votes
2answers
424 views

Equilibrium of Force Systems including Torque

please help me to solve this problem.. this is only the #3 on my homework and the only thing i didn't know here is how to calculate the tension T. please teach me how to solve the tension here ...
2
votes
1answer
82 views

Summing moments, where have I gone wrong?

Because I don't have enough rep to post images, the question is question 3 part iii) from here: http://www.mei.org.uk/files/papers/m209ju_jk32.pdf The surface at the contact point B is rough. The ...
0
votes
1answer
133 views

Find the bending moment of a pole attached to a moving block

I'm having trouble with the following problem. What I've done so far: x-y is the usual coordinate system. $a=\frac{F}{m}=\frac{800}{60}$ and the y component of this is $a_y=a\sin{60^\circ}$. To ...
3
votes
2answers
3k views

Calculating torque adjustment for offset of pivot point

I'm trying to figure out how much to adjust torque, on a torque wrench when using an extension that offsets the pivot point. See this calculator for a diagram of what I'm talking about: The trouble ...
0
votes
1answer
422 views

Torque and equilibrium

I am a little stuck on the concept involved in part b) of the following problem: A $5 m$ long road gate has a mass of $m = 15 kg$. The mass is evenly distributed in the gate. The gate is supported at ...
4
votes
1answer
624 views

Understanding moments as forces?

I was watching this lecture on analysis of stress for mechanics of materials. At time 7:20, the lecturer says that in equilibrium, the sum of forces and "moments" in each direction (x,y,z) must be ...
0
votes
1answer
419 views

Calculating torque in a structure

I posted this on math stack exchange but realize it is more a physics question. I have a structure which is set up as shown in the image. A weight hangs from point A with mass $m$. Joint B is free ...
3
votes
1answer
843 views

Why does the beam in a weighing balance get tilted proportional to the weights added to each pan?

I'm talking about a beam balance(a simple weighing balance with a beam and two pans hung on either side) As answered in a previous question, the beam comes back to the original position when one ...
3
votes
3answers
235 views

What is a “Center Of Mass” issue of a Gorillapod?

I read somewhere that a Gorillapod may have "Center Of Mass" issues when used with the long lenses. So, I wish to understand what is a "Center Of Mass" issue? I have to clarify that I am NOT a ...
0
votes
1answer
478 views

Can anyone solve this simple static equilibrium problem? [closed]

A bridge is 50m long, has a mass of 20,000kg, and rests on two pivots, A and B. The distance between A and the left side of the bridge is 10m. The distance between B and the right side of the bridge ...
1
vote
2answers
401 views

How do you choose the locations of forces when calculating moments?

A uniform bridge of weight 1200kN and of length 17m rests on supports at each end which are 1m wide. A stationary lorry of weight 60kN has it’s centre of mass 3.0m from the centre of the bridge. ...
3
votes
5answers
683 views

How much force would be necessary to hold a 6-foot steel staff weighing 20 lbs from one end of it, parallel to the floor?

This isn't a homework problem. I'm asking cause I'm wondering how strong a person would have to be to pull it off. Their arms would be extended, both hands gripping the staff at one end, and the staff ...