# Tagged Questions

76 views

### Distinction between torque and force

Distinction between Torque and Force. Consider a case when a cylinder is rolling down a rough inclined plane. While analysing its motion, we consider the force applied by the friction and the ...
29 views

### Maximum friction force for a wheel to be able to roll

The wheel with mass $M$ and radius $R$ below is free in space (it is not on the ground). A torque $\tau$ is applied to it through an engine. A horizontal force $F = \frac{\tau}{R}$ is also applied to ...
18 views

### How does ground interact with a box rotating around its corner?

I have some questions about how forces $F$, friction force $F_{friction}$, and normal $N$ interact in order to the box below to turn (clockwise) about the red corner, without sliding. The force $F$ is ...
146 views

### What causes a tall box to tip over on an inclined plane?

I'm wondering what makes a tall box rotate about its edge (the red point on the figure below) on a inclined plane (with or without slipping), when subjected to forces of gravity and friction only: ...
124 views

### Can a ball stay still while laying on a inclined plane?

Suppose there is a ball on an inclined plane. So, there are three forces acting on it: normal force from the plane, gravity (which can be decomposed in the component of gravity perpendicular to the ...
43 views

### Torque, and the Law of the Lever

How fundamental is the Law of the Lever? It seems that we simply define torque as being $r \times F$, if that's the case, then torque isn't a derived quantity, is it? Something like the Law of the ...
39 views

### At the instant of release of an object from rest. Is the only force that can act its weight?

Q3 from a mechanics exam past paper: I can do parts i) and ii) but for iii) in finding the angular acceleration, i used $C=I\alpha$, where $C$ is the applied couple or torque, $I$ is the moment of ...
53 views

### Free vs bound vectors and torque

When considering basic Newtonian mechanics, we can treat vector as free and move their point of application at will. This is consistent with the affine nature of Euclidean space. However, when ...
25 views

### What is the linear and rotational motions generated by a force not on the CG?

Given a force that is applied to a free body, not directly towards, or away from the centre of gravity, how would you calculate the amount of linear and rotational velocities generated, as the farther ...
68 views

### Torque due to Gravity

I have learned that a torque on an object due to the gravity can be calculated as if the gravity acts on the center of mass of the object when the object is near the surface of the earth. Now I want ...
73 views

### Falling off a chair, how best to save yourself

If I consider a man sitting on an office chair that reclines backwards iff you lean backwards. What could be done to prevent hin from falling? a) raising his legs till they are parallel to ground. ...
114 views

### Why doesn't a block rotate due to friction?

In a horizontal surface, a block (cube) is sliding due to a sudden push. When the block slides, there is frictional force which is acting on the block. Frictional force will have a torque around ...
82 views

### How can a reel of thread move in opposite direction?

There is a nice puzzle about reel of thread. I wonder why the solution works. The puzzle: You take a reel with threads on it. Inner radius r, outer radius R. You put it on a table. If you pull ...
28 views

258 views

### Why can you add moment vectors?

My book says the following: If the body is acted upon by a system of forces, the resultant moment of the forces about point O can be determined by vector addition of the moment of each force. The ...
277 views

### Would this box on the floor rotate based on friction?

There is a floor that friction is proportional to its velocity (like $F=-kv$) and there is a box with its width as $l$ and its height as $h$. (you may assume that $l$ is longer than $h$). It is on the ...
237 views

### Conservation of angular momentum

We were learning about angular momentum in class today, and although it sort of makes sense, it's much harder for me to think about than linear momentum. So from what I can tell: Angular momentum ...
3k views

### How does a car's low gear increase power while going slower?

People have always told me that when a car goes into low gear, it goes slower but puts "more power" or "more torque" on the wheels, which allows it to descend slippery slopes or get out of mud traps ...
800 views

### Torque of a winch with pulleys [closed]

I'm working on a project that involves using a remote-controlled electric winch to raise and lower my bicycle using a pulley system. The problem is that I don't know how much torque will be required ...
826 views

### Force acting on a simple rigid body in space

so this is the question that's been bothering me: Say you have a simple rigid body in space that is at rest or travelling with only translational motion at a constant speed. Say that the body is ...
224 views

### How to sum several thrust vector on a single object (like a plane)

I'm a developer. I tried (mostly for fun) to create a realistic physic engine. I try to sum all forces (here thrust) applying to an object in two composantes: an acceleration vector and the angular ...
137 views

### Why does this screwdriver roll in a curved trajectory?

I am trying my level best to give this screwdriver a horizontal push only, but it is going in a circular path. I thought of uneven friction due to non-uniform normal reaction...what do you think? I ...
162 views

### How do objects change their axis of rotation?

If I hold a pencil at its end and spin it, throwing it upwards, it will spin about its end, but will soon start spinning around its center. How is this? I would draw the following torque diagram for ...
I'm having trouble with the following problem. What I've done so far: x-y is the usual coordinate system. $a=\frac{F}{m}=\frac{800}{60}$ and the y component of this is $a_y=a\sin{60^\circ}$. To ...
In each one of the following figures there's a pole of length $1.2 \text{m}$ and there's a force $\vec F = 150 \text{N}$ acting on it. Determine the torque that is created by the force relative ...