3
votes
1answer
148 views

How is weight distributed when legs are astride?

Is there a simple and quick formula to find the weight (the force acting) on each leg, especially when legs are astride and they are not equally stretched? (or, better) not equally distant from the ...
0
votes
1answer
25 views

Finding directions of the internal forces within a freely jointed rigid object?

Consider the the following problem: Here is a force diagram showing the situation: For part (i) Taking moments about $B$ for $BC$ gives $84.5Lcos\beta=2LT$ So $T=39$N For part (ii) Resolving ...
3
votes
1answer
115 views

Forces acting on two balls in a jar [closed]

Consider the following situation: Two balls are inside a jar with diameter $D$. The balls are uniform in mass and both have the same diameter $d$. Express the forces that acts at the colored dots ...
0
votes
1answer
57 views

How to calculate the supporting force exerted by a stationary object (cupboard) and support (brackets) for it?

I have a wall mounted Stuva Ikea cupboard, which measures 60x64x30cm. The base is 64x30cm. It is already supported by 2 holes at the back base, (64x60cm). But I need to add in L shape brackets ...
-1
votes
1answer
65 views

How do I know which force to use in moments calculation?

I'm working on some Statics problem, with the method of joints, etc and for all of them, we use sum of moments = 0. However, I'm very confused about which forces I should use to find the sum of ...
2
votes
1answer
78 views

Relative strength of a dome

Is there a rough way to determine how the height of a dome affects the load that dome could support? For instance, assuming the bases of two domes are 24" in diameter, and one dome is 2" high while ...
4
votes
4answers
986 views

Blocks stacked on an incline connected by rope around pulley

Two objects A and B, of masses 5 kg and 20 kg respectively, are connected by a massless string passing over a frictionless pulley at the top of an inclined plane, as shown in the figure. The ...
0
votes
2answers
367 views

Calculating axle load in cargo container (pics are included)

I'm current developing cargo loader software, but i have a little challenge with calculating load for each axle when a cargo is placed on container. I know that all axles will be affected (the nearest ...
0
votes
1answer
101 views

Moment around a point in a frame

Note: Both diagrams are 2d(they might look 3d because I drew them manually.) I have a prismatic frame that looks like this: I made a section on the half of the first pillar(the red line represents the ...
-1
votes
2answers
113 views

Friction acting on mass on string

Assume we have some stationary point mass that would slide, if not for some coefficient of friction, along a light, inextensible string, attached to two points at different heights. Considering ...
1
vote
0answers
121 views

Question about moments? [closed]

Take a look at this diagram: http://www.chegg.com/homework-help/questions-and-answers/7-pipe-assembly-supports-vertical-loads-shown-determine-components-reaction-ball-socket-jo-q2260091 If you ...
0
votes
3answers
710 views

How to determine direction of forces in a static problem?

I am consistently getting this wrong. To me, in the picture below, it would make sense that the structure would be pulling downward, and the cable BD would be pulling upward - thus the system is in ...
1
vote
1answer
733 views

Tension on pulleys Physics Question [closed]

Collar A is connected to a 50lb load on a frictionless horizontal rod. Determine magnitude of P to maintain equilibrium when x=4.5. Im confused on the concept of Tension I originally got the ...
2
votes
1answer
85 views

Summing moments, where have I gone wrong?

Because I don't have enough rep to post images, the question is question 3 part iii) from here: http://www.mei.org.uk/files/papers/m209ju_jk32.pdf The surface at the contact point B is rough. The ...
8
votes
3answers
343 views

Where does the extra equation come from to determine the forces from an object on a table?

I have a question about basic statics but somehow I cannot manage to find the answer on my own (btw, this is not a homework. It's been so many years since school for me...). The problem is very ...
0
votes
2answers
1k views

How would you determine whether an object is at equilibrium? [closed]

How would you determine whether an object is at equilibrium or not? What is the definition of equilibrium?
0
votes
1answer
3k views

Problem solving moments in equilibrium

Two straight ladders, AC and BC, have equal weights $W$. They stand in equilibrium with their feet, A and B, on rough horizontal ground and their tops freely hinged at C. Angle CAB = 60$ ^o$, angle ...
0
votes
1answer
156 views

Find the bending moment of a pole attached to a moving block

I'm having trouble with the following problem. What I've done so far: x-y is the usual coordinate system. $a=\frac{F}{m}=\frac{800}{60}$ and the y component of this is $a_y=a\sin{60^\circ}$. To ...
-2
votes
1answer
441 views

Shear Flow corresponding to Eccentric Shear Force of a Closed-section Beam (Structural Analysis - Mechanics)

Been stumped with this question for way too long... its a beam with a thin-walled rectangular cross-section, and a shear force is acting at a distance from the shear center. I know my decomposition of ...
0
votes
0answers
41 views

How do I minimize the the stress created by fore-aft forces?

My friends and I are designing a bench press spotter. Essentially, when the user needs help lifting the barbell due to muscle fatigue, an arm on each side of the user raises to provide assistance. ...
1
vote
2answers
176 views

Additional mass of block on inclined plane

I would like some help in solving this problem. Height is 15 cm , base is 88 cm My attempt: $$(119.3 + m)(\sin(\theta)) = (88*9.8)$$ $$ 15^2 + 88^2 = 89.269^2 $$ $$ \sin^{-1} = 15/89.269 $$ $$ ...
1
vote
0answers
146 views

How can I calculate all of the tensions in the cords? [closed]

I have been stuck on this problem for the last half, and to be honest I don't even no where to begin. I'm being asked to calculate all of tensions for the cords. I know I'm supposed to use $\cos$ to ...
0
votes
3answers
247 views

Doubts with levers

I'm studying for a test of static rigid body and I'm having doubts on how to solve problems involving levers with weight. If I have, for example, a lever 10 kilograms and 3 meters long and one support ...
1
vote
1answer
773 views

Solving a Statically Indeterminate Truss with Energy Equations (Tricky)

Okay, first off, I know that there is a very similar problem about statically indeterminate trusses here, but my problem was a bit different and I didn't know how to adapt the answer for that problem ...
0
votes
1answer
2k views

How to calculate the supporting force for a cantilever beam? [closed]

How do I find the supporting force $R_A$ and the moment $M_A$? Should I use the sum of moments or?
0
votes
1answer
572 views

Trying to understand the tension in a spring with two weights attached [duplicate]

Possible Duplicate: Why I think tension should be twice the force in a tug of war For (A) in this image, I would think the tension should be should be 2mg. However, my book says the ...
0
votes
1answer
544 views

Can I use Newton's second law to solve what seems to be a torque problem?

The Problem: An 8-m-long beam, weighing 14,700 N, is hinged to a wall and supported by a light rope that is attached 2.0 m from the free end of the beam. If the beam is supported at an angle ...
4
votes
1answer
2k views

If 1 screw can support 120 lbs, how much weight can 25 screws support?

While this is mainly about my personal home improvement project, I figure this would be a good opportunity for some of you to apply your physics skills to a real-world situation. My situation is ...
0
votes
1answer
447 views

Torque and equilibrium

I am a little stuck on the concept involved in part b) of the following problem: A $5 m$ long road gate has a mass of $m = 15 kg$. The mass is evenly distributed in the gate. The gate is supported at ...
4
votes
1answer
695 views

Understanding moments as forces?

I was watching this lecture on analysis of stress for mechanics of materials. At time 7:20, the lecturer says that in equilibrium, the sum of forces and "moments" in each direction (x,y,z) must be ...
0
votes
1answer
463 views

Calculating torque in a structure

I posted this on math stack exchange but realize it is more a physics question. I have a structure which is set up as shown in the image. A weight hangs from point A with mass $m$. Joint B is free ...
3
votes
1answer
1k views

Why does the beam in a weighing balance get tilted proportional to the weights added to each pan?

I'm talking about a beam balance(a simple weighing balance with a beam and two pans hung on either side) As answered in a previous question, the beam comes back to the original position when one ...
0
votes
2answers
413 views

Hanging a Hammock

I have a hammock that I want to hang using a tree on one end and a wooden post set in a bucket of cement on the other end. How would I determine how heavy the cement needs to be so that it would ...
3
votes
3answers
5k views

Angles on swing sets

I'm building a swing set for my children. All of the designs I've seen involve building two A-frames and connecting them at the top with a crossbar/beam from which hang the swings. The A-frames are ...
3
votes
3answers
3k views

Deadlifting the rear end of a car with a lever. What it equates to in actual weight?

Consider this youtube video of a guy lifting a car. (skip to 2:15). I checked, and these cars (PT Cruiser) weigh $1417\:\rm{kg}$. What would the equation be to estimate how much weight he is actually ...
0
votes
1answer
533 views

Can anyone solve this simple static equilibrium problem? [closed]

A bridge is 50m long, has a mass of 20,000kg, and rests on two pivots, A and B. The distance between A and the left side of the bridge is 10m. The distance between B and the right side of the bridge ...
2
votes
0answers
1k views

Forces and torques about the CENTER OF MASS of a physical pendulum

I'm currently stumped by the following situation. Say we've got a rectangular physical pendulum (think ruler with a hole-punch at one end). It's trivial to analyze the motion of the pendulum with the ...
-1
votes
1answer
216 views

Find largest angle

The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the ...
1
vote
1answer
225 views

Finding the contact force in a mechanical problem [closed]

what is the proper FBD for this system. I cant decide since the weight is given, but there is tension and contact forces. Things get mixed up. Determine the contact force between the smooth 200-lb ...
1
vote
1answer
312 views

Wave equation from hooke law - simple question

In the paragraph http://en.wikipedia.org/wiki/Wave_equation#From_Hooke.27s_law it is said, regarding the u(x) function, that Here u(x) measures the distance from the equilibrium of the mass ...
0
votes
3answers
3k views

How do I find the tension in additional strings in this problem? [on hold]

A mass of 5.00 kg hangs attached to three strings as shown in the figure (see image below). Find the tension in each string. Hint: Consider the equilibrium of the point where the strings join. ...
0
votes
1answer
803 views

Solving an indeterminate triangle truss structure (statics)

From the setup of two trusses as shown in this illustration, how can I solve for the axial reaction forces in the trusses, and in the points A and B (Ax, Ay, Bx, By)? It is assumed that the joints ...
4
votes
1answer
1k views

Hooke's Law question

I have the following question to answer: a force of160 N stretches a spring 0.050m from its equilibrium position. A. what is the spring constant of the spring? The equation for Hooke's Law in my ...
0
votes
2answers
1k views

Calculate the weight a simple plank can support [closed]

I'd like to build a simple desk; just a single plank of wood (or a few side-by-side) with solid supports on each end of the desk. What I'm trying to figure out is how thick a plank I want to use for ...
8
votes
2answers
5k views

What is the force on the arms in a pushup?

What force do the arms have to generate to do a pushup? Let us look a this simplified model: The body can be represented by the green plank of mass B. Its angle to the ground is $\theta$. This ...
2
votes
2answers
2k views

Distribution of forces

(little background: I'm trying to develop a small, quick 'n dirty static physics engine to determine whether a stacking of boxes is stable). If I have a 3D rigid box (with the bottom in the ...
1
vote
4answers
3k views

Upward force on a object at rest

Is there an upward force on a object at rest? If yes, where does it come from?
-1
votes
1answer
379 views

Finding the mass of bed/Patient [closed]

One of my friends has a problem and we don't know how to get this done, We want to to know the mass of a patient who is laying on a bed. One scales was put under the foot of a bed and weighed 232kg ...
3
votes
5answers
747 views

How much force would be necessary to hold a 6-foot steel staff weighing 20 lbs from one end of it, parallel to the floor?

This isn't a homework problem. I'm asking cause I'm wondering how strong a person would have to be to pull it off. Their arms would be extended, both hands gripping the staff at one end, and the staff ...