1
vote
3answers
78 views

Distinction between torque and force

Distinction between Torque and Force. Consider a case when a cylinder is rolling down a rough inclined plane. While analysing its motion, we consider the force applied by the friction and the ...
1
vote
0answers
39 views

How torque and friction cause wheel to roll

I apologize if this question has been answered before, but I did not find the explanation that I needed. If a torque is applied to a wheel situated on a frictional surface, what forces cause the ...
7
votes
3answers
968 views

What determines whether a pool ball will bouce backwards after colliding with another pool ball?

I'm no knowledgeable pool player, but I've noticed that sometimes when the cue ball hits another pool ball, they roll together; and sometimes the cue ball bounces back. And I have a very, very rough ...
35
votes
6answers
5k views

How can the Earth keep spinning with a liquid core?

In regards to the 'conservation of angular momentum' being the explanation of why celestial objects spin... If you fill a ball or any other container with a liquid and try to spin it, you will not ...
1
vote
3answers
115 views

Why doesn't a block rotate due to friction?

In a horizontal surface, a block (cube) is sliding due to a sudden push. When the block slides, there is frictional force which is acting on the block. Frictional force will have a torque around ...
1
vote
1answer
110 views

Calculating the time to stop a wheel with friction [closed]

I'm trying to solve the following problem, but i have no idea how to begin. A wheel of mass $M$, radius of gyration $k$, spins smoothly on a fixed horizontal axle of radius a which passes through ...
9
votes
1answer
210 views

What makes a wrist-energized gyroscope rotate faster?

I'm considering a wrist-energized gyroscope, shown below (after my daughter let it fall and it broke open). That one was sold as Roller Ball, but variants are known as Powerball, DynaBee, Dynaball, ...
1
vote
2answers
124 views

Direction of friction for object that rolls with slipping

Let's say you hit a cue ball with a pool stick that causes an impulse. If the pool stick hits the ball above the ball's center of mass, is the direction of friction different than if the pool stick ...
2
votes
1answer
195 views

Push a box in a plane with friction. How to deal with the rotation?

Suppose I have a box (say, length-1m, width-1m, height-0.5m) on the plane with friction. I can apply a horizontal force in on the surface of the box. If the force doesn't pass through the center of ...
0
votes
1answer
147 views

Contradiction regarding friction of a rolling cylinder in an inclined plane

I came upon this while wondering whether the friction of a rolling cylinder on an inclined plane depends on the value of friction coefficient. now, $$f\leqq\upsilon N$$ Again after calculating I ...
1
vote
0answers
57 views

Is there any role of steering in turning?

I am aware of the practical requirement of turning the steering wheel to turn a car while going on a straight and even curved road. But in the proofs of turning of car on leveled or banked curves, ...
2
votes
3answers
271 views

Ideally speaking, will a rolling disk with no slipping come to a stop because of friction from the ground?

Consider a rotating disk on a horizontal plane with static friction. The contact point of the disk with the plane has null instantaneous velocity. Assuming the center of the disk has fixed $v_0$ ...
10
votes
3answers
486 views

What is the physics of a spinning coin?

When we spin a coin on a table, we observe 2 things: It slows down and stops after sometime. It does not stay at just one point on the table but its point of contact with table changes with time. ...
0
votes
4answers
238 views

Rolling motion of an accelerated body

I recently read in a book that static friction is zero for a rolling body, and this explains why it doesn't slow down the rolling body. However, if static friction is zero, how does the body grip the ...
3
votes
3answers
1k views

Why doesn't static friction decelerate a rolling body?

I know that static friction isn't the cause of deceleration of a rolling body. But if static friction is the only force in the horizontal direction, then shouldn't there be some acceleration produced ...
0
votes
1answer
473 views

Direction of friction in case of a rolling sphere

Suppose a ball rolls on a ground .obviously it is friction that helps to develop the required torque.Hence I find the direction of friction by pointing out the direction of rolling of the ball. But is ...
1
vote
1answer
281 views

What is the friction between cylinder and wall (ground)?

A hollow cylinder (radius $R$) is rolling against the wall at angular speed $\omega$. The coefficient of friction between the cylinder and the wall(ground) is $\mu$. After how many rotations the ...
11
votes
2answers
453 views

The secret behind the spinning, asymmetrically weighted, 2D disk-shaped top?

When you spin an asymmetrically weighted, 2D disk-shaped top, the heavy part actually rises to the top. Why is this? http://www.youtube.com/watch?v=h0SZZTBQmEs ...
4
votes
3answers
5k views

Static as opposed to Kinetic Friction in Rolling Motion

During analysis of rolling motion, why do we consider coefficient of friction as that of static friction and not kinetic friction?
2
votes
2answers
1k views

Angular momentum conservation while internal frictional torque is present

So this appears in a problem which looks simple enough in its context; It's something like this: Two discs, A and B, are mounted coaxially on a vertical axle. The discs have moments of inertia $I$ ...
19
votes
1answer
1k views

What determines the angle of the cushion on a pool table?

If you look at the cushions (bumpers) on a pool table, you'll see that they're not vertical. They're tilted inwards. About 10 years ago, I came across a physics exam in which one of the problems ...
2
votes
2answers
226 views

Approximating Rolling/Sliding in 2D Shape

I'm trying to find more information on how a 2D shape (could be defined by a function, such as ellipse, or by a polygon) will roll across a surface. The shape could be nearly circular or quite ...
2
votes
1answer
475 views

How does the resistance force on a rolling ball depend on the ball radius?

A billiard ball set gently rolling on a billiard table slows and stops, because it is decelerated by resistance forces at the contact between the ball and table. I expect the magnitude of the ...
1
vote
1answer
280 views

What controls whether a ball will skid or roll?

A billard ball is struck with a cue. The line of action of the applied impulse is horizontal and passes through the center of the ball. The initial velocity $v_0$ of the ball, its radius $R$, its mass ...
2
votes
3answers
178 views

Effect of surface treatment on fair dice

If I have a perfectly balanced and thus fair cubic die, then polish 3 adjacent faces (so that their coefficient of friction is effectively zero) and roughen the remaining faces (so that their ...
6
votes
1answer
198 views

Distance a curveball travels?

I've seen some discussions regarding the movement of a spinning object, say a curveball. However, all have been largely qualitative. I was wondering if anyone has seen or worked through a ...