1
vote
1answer
41 views

Cold welding of a metallic surface

I have heard of cold welding, it's said that it's only possible if the surface is very clean. Can cold welding be accomplished by shearing a metal object and then immediately touching the newly ...
0
votes
1answer
46 views

Grain boundary sliding in creep

To prevent grain boundary sliding so that creep is less likely to occur, usually engineers would design components of larger grains or have columnar grain structure to prevent grain-boundary sliding. ...
0
votes
1answer
31 views

A question about residual stress

Shot peening is a process of inducing residual compressive stress on the surface layer of metal parts. When shooting particles are colliding on the surface of metal there is a compressive stress. My ...
0
votes
0answers
8 views

Determining porosity in metals

I am in need of a book (preferably) or other reference material which would help technicians determine whether porosity exists in the fracture face of a tensile test bar for a variety of different ...
0
votes
2answers
114 views

Material breaking underneath its breaking point (due to repeated load)

I'm trying to recall some fact that I learned in my college materials science class, where we learned concepts like stress vs. strain. I remember that materials like metal have a breaking point, and ...
2
votes
0answers
90 views

Bubbling metal vapor through liquid Helium?

When a metal cools from its liquid state, part of the nucleation happens from pre-existing clusters (a group of unit cells of the crystal lattice) already present in the liquid. In the case of a ...
173
votes
11answers
36k views

Why don't metals bond when touched together?

It is my understanding that metals are a crystal lattice of ions, held together by delocalized electrons, which move freely through the lattice (and conduct electricity, heat, etc.). If two pieces ...
0
votes
0answers
55 views

Finding proportions of metal microstructures from eutectic diagrams

So I have an equilibrium phase diagram of steel and I am asked to 'Calculate the proportion of pearlite in the microstructure of 0.4 wt% C steel just below the eutectoid temperature (727 °C).' I have ...
3
votes
1answer
1k views

What causes stress concentration (aka stress risers/raisers) at corners?

I've read a few explanations about why stress concentration occurs at sharp corners but I don't find the explanations intuitive. Can anyone explain it perhaps using an analogy such as atoms "holding ...
2
votes
2answers
3k views

Will the hole on a metal disc expand or contract upon heating? [duplicate]

Possible Duplicate: Will a hole cut into a metal disk expand or shrink when the disc is heated? The metal disc of diameter D1 has a hole in it and the diameter of the hole is D2 (D2 Now, ...
2
votes
2answers
910 views

Properties to select suitable materials for making permanent magnets

I have read that soft iron is suitable for making a permanent magnet. Because it is required for permanent magnet to have high coercivity and high retentivity. Same text also said earlier that soft ...
1
vote
0answers
286 views

Electrical machines: electrical and mechanical properties of steels and cast iron

I would like to know a good source of information for the common metals (steels and cast iron). Information that I need are basically the mass density and the electrical conductivity or resistivity. ...
6
votes
1answer
1k views

What is the penetration length of static electric field into conducting metals?

How large is the penetration length for static electric field into good conductors? I have two versions: (1) few atomic spacings $$a\sim n_{e}^{-1/3},$$ and (2) Debye length computed by Fermi ...
8
votes
3answers
17k views

Hollow Tube Stronger than Solid bar of same Outside Diameter (O.D.)?

I was listening to some co-workers talking about problems meeting stiffness requirements. Someone said that even with a solid metal rod (instead of the existing tube) we could not meet stiffness ...
32
votes
8answers
25k views

Will a hole cut into a metal disk expand or shrink when the disc is heated?

Suppose you take a metal disc and cut a small, circular hole in the center. When you heat the whole thing, will the hole's diameter increase or decrease? and why?
6
votes
2answers
659 views

If sound wave is going to hit any metals can it make that metal electrons into exited state?

What will happen when sound wave hits the metals with very high frequency can it make the electrons to exited state. If it happens then what will be the state of that metal