0
votes
1answer
16 views

saturated water vapour pressure [on hold]

A pressure steel tube has a volume of 215 cc and contains air at 207 bar. It also contains some water (put it is 0.5 cc) deriving from the condensation of air humidity during pumping air into the ...
1
vote
1answer
147 views

Pressure and Buoyancy [closed]

It is well known that you can trap water in a drinking straw by placing the tip of your finger over the top while the straw is in the water, and then lifting it out. The inner diameter of the straw is ...
0
votes
2answers
46 views

Given a slanted pipe

Question: I have a pipeline that is tilted. I know the length of the pipeline, and the pressure (90psi) that is felt at the very bottom. I'm trying to find out how much liquid has leaked out if the ...
4
votes
3answers
524 views

Does the weight of fluid in a conical container act entirely on the base?

Scenario description Lets assume both containers have a capacity of 300 litres. One is a vertical tube as shown in pic 1 Other one is more or less a V shaped containers as shown in pic 2 Both are ...
5
votes
2answers
160 views

Difference between weight of water and pressure of water

(I didn't even have a basic formal education in physics. I'm learning through the internet out of my own interest, so if there are any silly mistakes, kindly bear with and guide me through.) ...
1
vote
1answer
33 views

Calculate electricity generation

A friend of mine stays near a water stream and wanted help to use its water. The height up to which the water could be raised using the water flow is 12ft. How much electricity can it produce? Is it ...
1
vote
1answer
117 views

Question about buoyancy

I took an empty clear sphere with radius r, put some weight inside this sphere, and put in into the water. I calculate the buoyancy force as: Volume of the sphere = Volume of the water displaced ...
0
votes
2answers
5k views

How to calculate gauge pressure at water depth?

I am creating a program that will calculate danger at water depths for sensitive equipment and maybe humans. How do I calculate the gauge pressure at a depth $D$. Lets say $D = 5000$ meters. My ...
0
votes
1answer
54 views

Hydrostatics , work Power and Energy [closed]

If a servant lifts 10 cubic meter of liquid from a tank, which is at a depth of 40m . If the work done by him is 1600J, then find the density of the liquid (g = 10 m/s^2)
-2
votes
2answers
239 views

Fluids and density [closed]

Is the answer C? Assume that you look at three objects that all float on water, but have different shapes and sizes. Which one has the greatest density? A.The object that has the largest fraction of ...
1
vote
2answers
494 views

Fluid Mechanics Piston Problem

The actual problem: A hydraulic car lift has a reservoir of fluid connected to two cylindrical fluid filled pipes. The pipe directly below the car has a diameter of 1.8 m. the pipe on which the ...
0
votes
3answers
400 views

Archimedes' principle for two liquid layers

Problem: I have a cylindrical vessel of height $H$ and radius $R$. There are two liquid layers in the vessel. The first has density $D_1$ and height $h_1$, the second has density $D_2$ and height ...
1
vote
1answer
143 views

What is the depth in meters of the pond? [closed]

A small spherical gas bubble of diameter $d= 4$ μm forms at the bottom of a pond. When the bubble rises to the surface its diameter is $n=1.1$ times bigger. What is the depth in meters of the pond? ...
0
votes
2answers
835 views

Pressure and height of water in a pipe [closed]

In a building, at what height does water rise from the ground-floor in a pipe, if the pressure there measures P=3atm? The correct answer is 31m. What formula should I apply?
-2
votes
1answer
61 views

Where does a sparkly (CO$_2$) water bottle have more presure [closed]

Where does a sparkly (CO$_2$) water bottle have more pressure? At a higher altitude (7000 feet) or under sea level (-8 feet)?
1
vote
1answer
395 views

Calculating pressure in accelerated fluids in closed and open vessels?

The question asked was "what should be the acceleration such that the pressure at both the points marked by thick dots be equal? the vessel is open and cubic with side 5m?" Initially i considered ...
0
votes
3answers
725 views

Pascal's law: pressure of fluid at different locations

I know that's stupid question, but I'm really confused what my teachers says, so I need to check that theory. Here are just two ordinary connected containers, which are full of water. On grounds ...
1
vote
1answer
114 views

Measure density with the help of buoyancy

I am trying to derive a formula to calculate the density of a irregulary shaped object. I can measure the (false) weight of the object in pure air (of known density), and the (false) weight of the ...
1
vote
0answers
88 views

Problem in average height

Let, diameter of cylinder hole of height 30m and diameter 2m filled with water. In a book, when author tried to find out the power for lifting all of the water then he used average height. why is ...
3
votes
1answer
472 views

Pascal law with two connected cylinders filled with water, and 50kg stones at both their ends

If I have two connected cylinders filled with water, and 50kg stones at both their ends (pressing both ends of the water) how much weight do I need to add on one side so that one of the stones reach ...
0
votes
1answer
100 views

In hydrostatics, is it possible for the bouancy to be greater than the weight of a body?

In the diagram we have two bodies, with density and volume $\delta$ and $V$, and a fluid $\ell$. $$\delta_1=0,7 \rm\frac{gr}{cm^3}$$ $$\delta_2=2 \rm\frac{gr}{cm^3}$$ $$V_1=100 \rm {cm^3}$$ $$V_2=10 ...
0
votes
3answers
12k views

Static Water Pressure vs Height [closed]

OK, so I have water at a known pressure, lets say 12psi. I have 2 pipes, installed vertically, one 2" diameter, the other 1/2" diameter. To what height (in feet) will the water raise to in each case? ...
1
vote
1answer
292 views

Proof of the Hydrostatic weighing equation?

I've been trying to derive this equation for about two hours: But I can't seem to get it. In my class, we are using it to accurately measure the volume of irregulary-shaped objects, but I ...