2
votes
1answer
84 views

How is circular motion possible on a banked road when there is no Friction?

It is given here that the maximum safe speed of a vehicle on a banked road having coefficient of friction $0$, is $V =\sqrt{R g \tan \theta}$, where $\theta$ is the angle of banking. I can't ...
3
votes
3answers
161 views

Conical vs Simple Pendulum

I don't understand why the Tension $T$ on a conical pendulum and a simple pendulum are different. In a simple pendulum, one would say that the tension of the rope is $T=mg \cos(\theta)$. However, ...
0
votes
1answer
65 views

Do we stand on the earth because of Newton's third law?

This is the question I encountered and I'm not sure I understand. The Newton's third law say that, when a body 1 exerts a force on the body 2, then the body 2 will exert the same force on body 1, ...
4
votes
2answers
175 views

If $F=ma$, how do can we experience both gravity and a normal force even though we are not accelerating

So as I sit in my chair, I experience a gravitational force pushing me into the chair and I'm also experiencing the normal force of the chair pushing back at me so I don't fall. According to Newton's ...
1
vote
3answers
230 views

Force when acceleration is zero

i tried to find it in books but i was unable to do so and i am not able to understand this and I couldn't think of a better example. i repeat. its just an example. if i punch someone's face with my ...
1
vote
2answers
143 views

Direction of force of friction?

I know that friction opposes the direction of the velocity, but the problem is when I don't know what the direction of the velocity is. When I'm drawing a FBD for complex systems with ramps and ...
0
votes
2answers
104 views

Is my free diagram of a spring stretched on one end and attached to the wall on the other end correct? [closed]

Consider the following figures. The top one shows the construction of a spring where its left end is attached to the wall and its right end is stretched by a force. The bottom one is supposed to be ...
-1
votes
1answer
91 views

What stops the car?

Centre of mass of a system cannot change its state of motion, unless there is an external force acting on it. Yet the internal force of brakes can bring a car to rest. Then what stops the car?
0
votes
1answer
96 views

Confusing Classical Mechanics Question

I don't want this to be a "do my home work question" so please tell me how I can make this question helpful for other people. In my physics assignment I found the question below. I'd think that both ...
3
votes
1answer
136 views

Force on bolt holding up jet engine on plane

I am to solve the following: A jet engine of mass $m$ is fastened to the fuselage of a passenger jet by a bolt. During flight, the plane encounters turbulence, which suddenly imparts an upward ...
-6
votes
3answers
191 views

Can you lift a basket up while standing inside it? [closed]

Suppose you stand in a basket and you try to pull the handles of the basket. Will you be able to lift the basket from ground? Similarly, Baron M√ľnchhausen allegedly pulled himself and the horse on ...
1
vote
4answers
266 views

Action Reaction when I pushing a trolley?

I tried to explain how those force work but I can hardly figure it out. I exerted a force on the trolley and there will be a force on trolley on me as well. This is the newton's third law. But why the ...
0
votes
4answers
438 views

How can acceleration $a$ be zero when applied force $F$ is non-zero?

An object is at rest and stays at rest, but an attached rope pulls with increasing force. What is the acceleration? The correct solution is that acceleration is constant and 0. Obviously $a= dv/dt ...
1
vote
1answer
427 views

Newton's Third Law of Motion

I want to start off by saying that I've looked around for other explanations, but I've not really found any satisfying ones. My question is basically the whole "Why can anything move at all?" ...
2
votes
1answer
711 views

Static Friction in Free Body Diagram (FBD) of Car parked on Incline

I'm working on a sample problem and it asks on how steep of an incline can a car park? From what I learned the friction is in the opposite direction if there was motion in said friction-less ...
2
votes
1answer
158 views

Vertical Load Reactions On A Ramp

Hello, I'm working on a small hardware project. I have two load sensors located at distance $S_1$ ($x=0$) and $S_2$. Assuming we ignore the weight of the ramp ... What is the load on $S_1$ and ...
28
votes
5answers
9k views

With Newton's third law, why are things capable of moving?

I've got a rather humiliating question considering newton's third law "If an object A exterts a force on object B, then object B exerts an equal but opposite force on object A" -> $F_1=-F_2$ ...
-1
votes
1answer
551 views

How should I draw this free-body diagram?

The horizontal force P acts on the rim of the homogeneous cylinder of radius R and weight W. Determine the smallest coefficient of static friction that enables the cylinder to start rolling up the ...
2
votes
1answer
2k views

Rolling resistance and static friction

I am a bit confused about the relation between rolling resistance and static friction. I have often heard that it is the static friction that lets the wheel roll. Consider the following two cases: ...
1
vote
1answer
2k views

Two problems with free body diagrams. Contradictions (solutions are provided)

This problem is similar, but also different question from my previous question. They are both unfortunately long. Problem/Solution #1 ! ! Quick Concept Check a) Could someone briefly explain to me ...
2
votes
1answer
581 views

Why is static friction omitted here? And comparison with this problem on Newton's second Law. Solutions are all provided

The problem itself is short, but my concept question is...long. So be prepared. Note that problem 1 and problem 2 are related to my concept questions, so I am not taking advantage of asking two in ...
1
vote
2answers
2k views

How do I properly use Newton's Third Law and Free Body Diagrams?

A force of 14.0N is applied to a block as shown in the diagram below ! If the coefficient of friction is between the surface and the blocks is 0.35 a) What is the acceleration of the two blocks? ...