0
votes
0answers
19 views

Solving for currents in a circuit [on hold]

I need help finding the three listed currents in the figure below. Attached on the bottom is the solution for this problem, however I do not quite understand how they came up with the answers. ...
-3
votes
0answers
27 views

Solve the following linear second order circuit [on hold]

I am not able to solve for the second part of the question (when v(t) = 0)
1
vote
0answers
18 views

Neutral wire capacity [closed]

I have three DC circuits in my solar array. I have a three lead + ground (bare copper) tec armoured cable (#6). Why not run one circuit using the bare ground as negative? In fact, why not run three ...
1
vote
1answer
65 views

Differential Equations for Block Diagram of Satellite Attitude Control System

I am trying to understand the procedure to setup differential equations from a block diagram. The enclosed example is about the attitude control of a satellite. The ultimate goal is to find a ...
0
votes
0answers
51 views

Circuit analysis, calculating voltage across resistor [duplicate]

i'm solved this question, I'm sure that solution is right, but my instructor says that V1=116V, and also he said that he will not show how he get this result.Please help to identify who is right.
0
votes
0answers
49 views

Charge Amplifier response and frequency response [closed]

I am getting ready for my final and have completed everything on my study guide except for two questions I cannot figure out. Here is the first question: I have gone through all my lectures and ...
0
votes
0answers
19 views

How does band narrowing (heavily doping the emitter) affect the alpha F and alpha R in the Ebers-Moll model of a BJT?

I think that when the emitter is heavily doped, the bandgap is reduced which increases the reference forward current(current flowing through the E-B junction ) but the alphas themselves do not change. ...
0
votes
2answers
236 views

How do I combine three resistors which are in parallel with each other?

For this circuit (a and b are connected by a battery), Will I be able to find the total resistance of the circuit by adding resistors that are in series and combining resistors that are in ...
0
votes
1answer
49 views

Applying more current? [closed]

An electric motor draws 20 Amps, when at maximum load of x. Can that value of current be applied even if the load was ten times less than x from a certain power source?
1
vote
0answers
393 views

Help making a solenoid engine [closed]

I am currently working on a school project and my aim is to build an electric motor using DC. I am looking at a design similar to this: Solenoid Engine and I have built majority of it however I am ...
1
vote
4answers
2k views

Transformer: primary side & secondary side current 180 degree out of phase

I am a novice in electrical engineering. I notice that in transformer the secondary side current & current referred to as primary are 180 degree out of phase from each other. But why it is so, I ...
0
votes
1answer
79 views

Current in AC circuit

The problem is to find the current on the capacitor. $I''$ should be correct, but I don't know how to construct the formula for $I'$. I managed to get the value for $I_c$ using Thevenin and Norton ...
1
vote
3answers
307 views

Power transfer in a transformer

Can it be proved using the concept of induced emf that power supplied at the primary coil equals power consumed at the secondary. I tried following. Let primary coil be called 1 and secondary be ...
2
votes
1answer
477 views

How we approach RLC circult from RLGC model?

In the text, it introduces a practical model to investigate a transmission line (like BNC cable), it considers the transmission line has resistive $R$, inductance $L$, conductance $G$ and capacitance ...
-1
votes
1answer
89 views

Differentiating a sinusoid [closed]

http://i.stack.imgur.com/ndLgm.png I don't see the how the author derived that $\frac { dv }{ dt } \leftrightarrow\overrightarrow { V } j\omega$.
0
votes
2answers
8k views

How do I calculate output voltage from a given supply voltage and resistance?

I have searched everywhere but I can't seem to find out how I can calculate the output voltage (or voltage over a component) from the resistance of a resistor (or other component) and the supply ...
1
vote
1answer
1k views

How to calculate the charge and the potential across a charged capacitor charging an uncharged capacitor?

Initially, there is a single capacitor $A$ attached to a power source that charges it to a certain voltage $V$. Once it is charged, it is instantaneously removed and placed in a circuit with an ...
5
votes
6answers
8k views

What would be the effective resistance of the ladder of resistors having n steps

I'm a tutor. This is a high school level problem. In high school, every one have might have solved a problem of effective resistance of a ladder of resistors having infinite steps. Now the problem is ...
0
votes
1answer
205 views

Waveforms for a given ideal inverters circuit

I have the following circuit. All the inverters are ideal CMOS. I need to draw the waveforms for each point (A, B, D, E, Vo), given that waveform at input. What I want to ask is if what I did so ...