Physics Stack Exchange is a question and answer site for active researchers, academics and students of physics. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

Starting with a pot of cold tap water, I want to cook a hard-boiled egg using the minimum amount of energy. Is it more energy efficient to bring a pot to boil first and then put the egg in it, or to put the egg in the pot of cold water first and let it heat up with the water?

share|cite|improve this question
Green wisdom says: 1. Put eggs in stove, pour water 2. Wait for water to boil 3. Switch off stove 4. Wait some minutes (browse this site) 5. Enjoy eggs. As an aside, I do not support such questions on this site. Atleast until the physicstheory.SE starts. Hence the downvote. I do not see any point in even doing back of the envelop calculations for this. – Approximist Mar 19 '11 at 4:03

Break egg into vacuum vessel, lower pressure until egg boils (sorry don't have a phase diagram for eggs handy)

share|cite|improve this answer
If I +1 this I'm not going to admit it. How about: Expose egg to near vacuum which exists in a very high percentage of the volume of the universe (0 Joules). – Carl Brannen Mar 19 '11 at 7:36
RE phase diagram: Eggs "boil" as water does, there is water and rather high molecular proteins in an egg, which raise boiling point marginally only. Difference is the tendency to overheat, due to lack of "seed" and viscosity. – Georg Mar 19 '11 at 11:24
@Carl - the cost if the ticket is rather high – Martin Beckett Mar 19 '11 at 14:30
@Martin Beckett; The OP didn't ask what the most efficient way to boil an egg is "on the earth". So one must assume that he means at a randomly chosen spot. Which is therefore likely to be intergalactic space. – Carl Brannen Mar 20 '11 at 3:46
This method won't actually cook the egg, will it? It'll just boil it. There's a difference. – Peter Shor Mar 23 '11 at 14:44

I know the answer :).

The most energy efficient way to get a hard boiled egg is to have a pot with a good cover on an electric range.

1)cover the bottom of pot with 1mm water, put eggs in and pot on the range and and turn it on to the maximum.

2)when the cover starts popping, turn off heat completely, leave it on the range, for the residual heat.

3)wait 3 minutes for very soft, 4 to 6 for medium and 8 or more for hard.

Pot with good cover means the cover is not popping once the heat is off.

share|cite|improve this answer
+1 The reason cookbooks don't recommend this method is it takes different amounts of time for water to start boiling, depending on both the range and the amount of water. So if you don't use the same range and the same pot (with the same amount of water) all the time, the egg won't come out consistently the way you want it. – Peter Shor Mar 23 '11 at 14:49

"Energy efficient" usually means "with minimal production of entropy". For that you need, 1) a well insulated (on the sides) pot, 2) minimal loss from heating element, 3) the smallest possible (and practical) amount of water amount that can boil an egg (i.e. conver its whole surface) and 4) put the egg at the beginning of the process (not drop it once the water boils because that generates extra entropy because of the temperature gradient).

Pressure cooking can be more efficient because it needs less time of the heating element. But since the temperature reaches more that ~100°C that can give a different cooking process, and not qualify as a "boiled egg" because of changes in taste and consistency.

share|cite|improve this answer

My cookbook says an egg should simmer in water for about 10 minutes. If you wait till the water simmers and then add the egg, the water will start boiling again in a few seconds, then needs to simmer for the 10 minutes. The heat of vaporization loss takes place for about 10 minutes. If the egg is placed in cold water first, it'll cook in fewer than 10 minutes of simmering as the pot heats up to boiling, so the heat of vaporization loss will be less than 10 minutes.

share|cite|improve this answer

A cooked egg has a lower free energy at room temperature and pressure than an uncooked egg (see this link, protein denaturation is complicated, but generally exothermic at room temperature). So boiling an egg does not require energy, it releases energy.

So it is most energy efficient to put the egg and water in a closed container, and use a reversible process to heat the water to boiling temperature. Then use the same pump in reverse to remove the heat. This cycle will net you a little bit of energy when all is said and done.

One simple way to do this is have the water touching a gas through a metal wall in an insulated container, so that the heat can flow, but the wall can sustain a large pressure difference. Then compress the gas slowly to raise the temperature of the gas and water to boiling temperature (this requires an enormous room-sized air-vapor container). If you do it slowly enough, the egg will be cooked when you reach 100 degrees, then you slowly relax the piston back to its starting position, recovering all the energy you put in, and a little more, due to the heat released by the egg as it was cooking.

This is a theoretical answer. The right answer for green purposes is that residental energy consumption is not a significant enough fraction of the total energy consumption for these measures to have any impact. So this type of conservation doesn't do anything, except keep yourself and others aware. To do something real, drive less and encourage energy efficient processes at work.

share|cite|improve this answer

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.