Take the 2-minute tour ×
Physics Stack Exchange is a question and answer site for active researchers, academics and students of physics. It's 100% free, no registration required.

Is there a detailed description for a Hartmann mask based collimation process?

I've been told by a friend that is possible to collimate an SCT by placing a three round holes Hartmann mask at the secondary and then covering one hole at a time. Unfortunately the guy did not clearly describe the full procedure and what I should try to obtain looking in the eyepiece (or looking at an attached webcam video).

share|improve this question
    
Look at Bakhtinov's mask - it is much easy to use –  Oleg Dok Jan 12 '12 at 6:31
    
Take a look at this post: physics.stackexchange.com/q/25560/2451 where Geoff Gaherty recommends Star Testing Astronomical Telescopes (Harold Richard Suiter/Willmann-Bell) and Telescope Optics by Rutten and van Venrooij. I know Star Testing Astronomical Telescopes talks about Hartmann mask, I'm just not wise enough to tell you if it is sufficient. –  TryTryAgain Jan 12 '12 at 9:41
    
I already own a Bahtinov mask and is really useful to focus, but is not the mask suggested by that friend to collimate the SCT –  Mario Jan 13 '12 at 8:14
    
...and I also own the wonderful book by Suiter: the mask is described but building it is not enough for me. The book also describes a couple of collimation processes: a day light one and a star based one. Both are quite easy but involve an "un-aided eye" approach. I would prefer a more ... assisted / precise method –  Mario Jan 13 '12 at 8:17
add comment

2 Answers 2

up vote 3 down vote accepted

The described procedure is suitable for an SCT telescope.

See bottom for reference URLs of images/blog posts/instructions to build the mask. See bottom also for an easier method (without mask) if you have a webcam adapted for telescope usage and a pc connected to the SCT mount.

"Apply the Hartmann mask to the telescope and align the three holes at 120 degrees with three adjustment screws on the secondary mirror. Point a star bright enough (eg. magnitude 1 or 2), using a high magnification (we may also need a night with good seeing, but that's another story ...) and you focus . If the telescope is not collimated, not get to see a single spot of light move and symmetrical, but you'll probably see a patch of distorted and elongated. It does not matter for now.

During the procedure, adjust the position of the telescope so that the star that you are using is always the center of the visual field.

Referring to the figures, we will call A , B and C (clockwise) the three collimation screws and the holes on the mask.

Temporarily cover the hole A with a piece of paper, cloth, or what you will, so that no light can enter through this hole (I use a post-it). Focus, bringing the two spots of light to match each other.

Remove the cover from the hole A and attach it to hole B . You should see 2 points of light, or an oblong spot. Do not touch the focus , but act on the collimation screw A until the two points of light unite .

Focus again, then move the cover from the hole B to hole C . Act on the screw B until the two points of light do come together again.

Focus again, then move the cover from the hole C to hole A. Act on screw C , until the two points of light do come together again.

Repeat the above steps until the point star will appear in all conditions. In the end, free all the holes and check the symmetry of the image you see. You can even fine-tune the collimation repeating the procedure with a higher magnification.

Confirmation that you have worked well will come observing the image of a star with no mask and at the highest magnification (2-3 times the diameter of the telescope in mm): If the diffraction pattern is perfectly symmetrical, then the telescope is perfectly collimated (bad seeing may prevent us from making this check)."


Original instructions can be found here: http://gerlos.altervista.org/collimazione-telescopio-sc-maschera-hartmann . In Italian but you can easily get it translated by Google.

Here are the same instructions in French: http://colmic.free.fr/collim/collimat.htm

And here are some good instructions to build the mask: http://www.iceinspace.com.au/63-187-0-0-1-0.html

A nice and free software that allows you to collimate using a webcam and a star. Seems very fast and even more precise: http://www.astrogeeks.com/Bliss/MetaGuide/

share|improve this answer
add comment

I'm the original author of the Italian instructions pointed out by Mario (tahnks for your translation in English!). Feel free to ask questions in English if you don't understand something or if something doesn't work.

One important point to add is that it's better to use a mask with triangular holes instead of circular ones: this way, when you are close to focus you will see 6 spikes of light from the star, and pseudo-Airy disk in diffraction pattern will be smaller. You can also judge your collimation looking at the symmetry of that pattern. If some spikes are brighter than others, or not equally spaced, you need a better collimation.

You can judge the quality your collimation also when focusing with a Bahtinov mask (the definitive focus aid, imho). Looking at the symmetry of the pattern generated by the mask and rotating the mask you can see if the telescope need recollimation or not.

For some images of symmetrical patterns with various focus aids you can check this page (it's in Italian, but the shots should speak for themselves): http://gerlos.altervista.org/maschera-bahtinov-messa-fuoco-super-precisa

share|improve this answer
    
you're welcome! thank you for the blog post! –  Mario Jan 16 '12 at 10:40
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.